SCHOCK 35

Standard Description

HULL

h  100% Hand lay-up fiberglass with balsa sandwich

h  Flush through-hull fittings

h  90-degree turn shut off valves

h  High gloss gel coat

h  Fiberglass-bonded hull pan

h  Glass biaxial unidirectional

h  Glass roving

h  Hull and deck joint bonded with 3M-5200 and bolted on 4” centers

 

KEEL

h  4500 lbs cast lead

h  8 ss keel bolts

 

RUDDER

h  Stainless steel rudder stock

h  Fiberglass rudder blade with high density foam core

h  Tiller extension

h  Varnished oak and mahogany laminated tiller

h  Glass biaxial and unidirectional glass roving

h  Rudder bearings

 

DECK AND DECK HARDWARE

h  100% hand lay-up fiberglass

h  Glass used as biaxial and unidirectional glass roving

h  Balsa sandwich and marine plywood sandwich in load bearing areas

h  Aluminum toe rails bolted on 4”center

h  Molded hiking ramps

h  Non-skid on deck, cabin top, cockpit sole and seat top

h  Two Harken #48.3A 3 speed 2 gear genoa sheet winches

h  Two Harken #32.2 STA halyard winches

h  Two Harken one speed grip winch handles

h  Two double Spinlock halyard stoppers

h  All deck blocks are lead aft to the cockpit

h  Two Harken adjustable under load genoa car and track systems

h  Harken roller bearing traveler with control lines

h  Double lifelines and stanchions

h  Welded stainless steel bow and stern pulpits

h  Four mooring cleats

h  Six tinted plexiglass cabin windows

 

INTERIOR

h  4-inch pilot berth and seat berth cushions

h  Settee berth backrest cushion with pigeon hole storage behind

h  Sit down navigation station with storage for charts and shelf for instruments

h  Oiled teak bulkhead and cabinets

 

GALLEY

h  Large ice box with a pump

h  25 gallon water tank

h  Stainless steel sink with foot pump

h  Plastic laminate galley counter top

h  Hideaway stove top cover

h  Large condiment storage with shelf and tinted acrylic sliding cabinet doors

 

HEAD COMPARTMENT

h  Marine head with holding tank

h  Mirrored sliding doors and vanity

h  Hanging locker

 

TANKAGE

h  17 gallon fuel tank with deck fill

h  25 gallon water tank with deck fill pump plate

h  9 gallon holding tank with deck pump plate

 

PROPULSION

h  Yanmar 3GM30F

h  3 cylinder in-line marine diesel

h  Fresh water cooled

h  Cast brass propeller strut

 

h  1 inch ss propeller shaft

h  Raw water filter on engine intake

h  Fuel and water separator

h  Cockpit engine instrument panel with tachometer, key start and alarms for oil pressure, water temperature and electronics

h  Martec folding propeller

 

MECHANICAL AND ELECTRICAL

h  Two 12-volt 90 amp hour batteries

h  Circuit breakers on the electrical panel with battery switch and battery condition meter

h  Running lights

h  Bow lights

h  Cabin lights

h  Chart table light

h  Manual bilge pump

 

SPINNAKER EQUIPMENT

h  Port and starboard spinnaker halyards

h  Spinnaker pole topping lift

h  Spinnaker track on mast

h  2-part spinnaker pole butt lift system

h  2 spinnaker sheet blocks

h  1 spinnaker pole

h  1 spinnaker pole foreguy

h  1 spinnaker pole foreguy block

h  2 spinnaker sheet cleats

h  2 spinnaker sheets  

 

SPARS AND RIGGING

h  Keel stepped mast

h  Sliding adjustable mast step

h  White epoxy painted aluminum mast and boom

h  Tri-sec tapered mast section

h  Four airfoil painted aluminum tapered spreaders

h  All rod standing rigging

h  All internal halyards

h  One main halyard

h  One genoa halyard

h  2 spinnaker halyards

h  All halyards made of composite material

h  Hall Spar quick-vang

h      Combination outhaul and flattening reef - internal

h  Two interior reefs with lock-off at the gooseneck

h  Color-coded lines

h  Running checkstays

h  Tube inside mast for mast cables

h  Fine tune mainsheet system and Barney post

h      Cunningham system:  3 part self-cleating at base of mast